Cleaners

Flushing Oil

It is highly effective flushing oil, which removes carbon and varnish deposits of the oxidized oil and other contaminants. It also leaves after displacing the carbon deposits, a thin film of synthetic lubricant, which will act as a light lubricant and rust preventive. It is normally used for cleaning and flushing of equipments and components which are subsequently lubricated with synthetic oils.

BENEFITS:

  • Removes carbon and varnish deposits.
  • Cleans engines, gear boxes, bearings, chains, hydraulic systems, air compressors etc.
  • Cleans pipelines, tanks and machinery components, which are lubricated by oil circulation systems.

APPLICATION: It is normally used for internal cleaning and flushing of engines, gear boxes, hydraulic systems, Air Compressors, Oil Circulation systems of equipments which are subsequently lubricated with fresh lubricating oils.  It is especially suggested for use when synthetic oil is charged afresh.

Unit packing : 27-litre drum and 210-litre drum

Anti-static spray cleaner for Cots & Aprons

CVC TEXCLEAN is a non-flammable, non-hazardous product that is inherently biodegradable and will remove all dust, dirt, fluff and other contaminants such as oil, grease, waxes and silicones from cots & aprons, rubber, rollers, belts & conveyors and similar surfaces.

Benefits:

  • Non-staining antistatic spray.
  • Removes all carbon and gummy.
  • Fast acting and safe.
  • Removes all carbon and gummy deposits.
  • Extends fluff cleaning interval between lapping considerably.
  • Eco-friendly cleaner.

Application:
Spray on contaminated and dirty surfaces and allow it to work for a short time and wipe off the surface of components such as Cots and Aprons, Top & Bottom rollers, Guide rollers of draw frames after which the components can be wiped off i.e. Cots and Aprons, Top & Bottom rollers, Guide rollers of draw frames, speed frames, ring frames.

Unit packing : 550-ml. Aerosol Tin and 5-litre carboy

Knotter / Splicer Cleaner

TEXLUBE is a non-staining cleaner-cum-lubricant for modern textile machinery used for various operations such as Spinning, Winding and Weaving, Knitting etc. Based on a specialty cleaner, synthetic lubricant and other chemical additives, it immediately penetrates and cleans fluff, dust and other deposits accumulated on surfaces. Further it leaves a thin, non-staining and non-sticky film of lubricant, which protects the exposed surface form rust & corrosion and reduces the wear & tear of moving parts. It is specially formulated for knotter/splicers of Schlafhorst, Murata Savio & Padmatex autowinders.

BENEFITS:

  • Cleans Carbon & Fluff deposits.
  • Lubricates the delicate Machinery.
  • Protects from rust and corrosion.

AREA OF APPLICATION: Knotter of autoconers and winders, spinning and weaving machinery, knitting and sewing machines, delicate mechanisms and other high speed equipments.

UNIT PACKING: Available 550-ml.Aerosol Tins with extension lube for pinpoint application.

Sewing and Knitting Machinery Cleaner

CVC KNITKLEEN SPRAY is a high quality organic cleaner which cleans, penetrates and protects all delicate machinery and parts which are in motion in knitting and sewing machines. It is also a non-staining, anti-static, non-freezing cleaner suitable for cleaning of profile/groove of butt and latch of needles of knitting machines. It removes all gummy and fluffy deposits from the contaminated surfaces by penetrating under the contaminants and dislodging them from their roots. These contaminants will then be easily removable by blowing air. It is an environmentally safe cleaner.

Benefits:

  • Non-staining and anti-static.
  • Completely washable.
  • Deep penetrating and fast acting.
  • Removes all carbon and gummy deposits.
  • Eco-friendly cleaner.

Applications:

  • Needles, sinkers and cams of knitting machines
  • Cleans chains, gears and bearings.
  • General cleaning and de-greasing textile machinery.

Packing: 550-ml. Aerosol Tin

Instant Stain Remover

CVC SR-100 is a fast acting effective stain removing spray which removes oil and grease spots from cotton, woolen, rayon & synthetic fabrics.

BENEFITS:

  • Effective stain removing spray
  • Removes oil and grease stains from fabric instantly.

APPLICATION METHOD:
Spray CVC SR-100 directly on the oil spot and wet it thoroughly. Allow SR-100 to work for a few minutes on the spot till a dry patch appears. Tap the patch gently and shake off any residue from the spot area. Use steamer over the spot area till the spot disappears completely. Where steamer is not available, steam iron may be used repeatedly till the spot disappears.

PACKING: 550-ml. Aerosol Tin

Dry Film Moly Lubricant

MOLYLUBE is clean, dry lubricant, based on molybdenum disulfide, chemically inert, forms a thin tenacious antifriction film capable of withstanding extreme pressures (100,000 psi) and temperatures (-180°C to +400°C). Protects against seizure, fretting, scoring etc. and will free seized threaded connections with deep penetrating and lubricating action.

AREA OF APPLICATIONS:

Bearings, slides, ways, shafts, journals, gears, rams, fasteners, chain wheels, conveyor, sprockets, pins, bushes, plungers, springs, hinges, threaded connections, locks, linkages, splines, sleeves, etc.

BENEFITS:

  • Clean, Dry Lubricant.
  • Inert Lubricant.
  • Permanent Lubricant.
  • Running-in Lubricant.
  • Extreme Temperature Lubricant.

PACKING: 550-ml. Aerosol tin and 5-litre Carboy.

Anti-Static Reed Wire Cleaner

An excellent Anti-Static agent with Synthetic lubricants specially developed for cleaning the yarn deposits, fluff, dust & other contaminants on the reed wires of high speed looms. The non-staining Synthetic lubricant ensures lubrication of the reed wires preventing further fluff deposits without affecting or harming the reed or the fibre.

APPLICATIONS :
For cleaning yarn deposits on the reed wires of high speed weaving looms. It may also be used for removing fluff and other contaminants on other Textile Machines and protect them from rust.

BENEFITS :

  • An excellent cleaner for filament and yarn deposits on the reeds.
  • Protects from Rust & corrosion.
  • Lubricates Reed wires & Increases life.
  • Does not attract fluff, dust etc. being Anti-static in nature.

PACKING: 550-ml. Aerosol Tin.

Oils

Synthetic Compressor Oil

COMPLUBE-280 is a fully Synthetic Compressor Oil specifically developed for Rotary Screw Compressors.  It is formulated with latest friction reducing technology to provide Long Life, Energy Savings & High Performance.  Also it is fortified with Antifoaming agent, E.P. additives, Rust & Corrosion Inhibitors for heavy duty lubrication for wide operating temperature range. These oils are available in wide range  of viscosity for all Screw Compressors.

Application:

  • For Rotary & Screw Compressors.
  • Lightly loaded gears.
  • Hydraulic systems.
  • Centralized lubrication systems.

Benefits:

  • Energy Savings (6-7%)
  • Extended drain intervals.
  • Improves life of filters elements.
  • Reduces maintenance cost.
  • Does not leave any carbonaceous deposits.

PACKING: 27-Litre drum and 210-litre Drum

Semi-synthetic Gear Oil

It is a specially formulated gear oil with anti-foaming agents and friction modifiers to facilitate high performance, longer life and saving in energy. It is also available in different viscosity grades such as ISO VG 32 / 40 / 68 / 100 / 150 / 220 / 460.

Benefits:

  • Extends drains intervals.
  • Reduces wear and tear.
  • Wide operating temperature range.
  • Reduces power consumption
  • Chemically inert.

Area of Application:
Enclosed Gear drives, Windmills, Transmission chains, Heavily loaded low speed antifriction bearing, Centralised lubrication systems, As a running-in-oil for OEMs. Heavy duty Earth moving and Excavating equipments.

Packing:
1-Litre Bottle & 27-Litre Drum.

Multifunctional Oil

This is a semi-synthetic high performance lubricating oil specially developed to provide long term lubrication, reduced wear and tear, wide temperature range and virtually no carbon deposits.  It is fortified with anti-corrosive, anti-oxidant, and E.P. additives with friction modifiers making it suitable for versatile applications such as compressor, hydraulic, gear and machinery oil. It is meeting IS:10522–1983 specification.

Benefits:

  • Single oil for many applications.
  • Reduces friction and wear.
  • Operates under wide temperature range.
  • Consumes less power.
  • Reduces oil inventory.

Area of Application:
Lightly loaded Gear and Gear Trains. Cam followers, Guide ways and Slide ways, Centralized Lubrication Systems, Gear boxes of circular Knitting machines etc. It is also a good lubricant for hydraulic systems chains and bearings of Textile machineries.

Packing :
1-Litre Bottle & 27-Litre Drum.

Synthetic Spindle Oil

This is a specially formulated eco-friendly long life spindle oil for the lubrication of high speed Textile spindles to provide energy saving, long life to spindles. It is available in different viscosity grades to suit the end use requirement of high speed, load and temperature and environmental conditions of Textile spindles and similar applications. It is a non-staining synthetic oil which does not leave any carbonaceous deposit. Due to its excellent lubricity it reduces the power consumption of spindles by 8 – 10%.

It is also available in different viscosity grades for Doublers, TFO Twisters and other high speed textile machinery.

AREAS OF APPLICATION:

Machinery components such as spindle bolsters of Ring frames, Doublers, TFO’s in Textile Industry for lubrication of high speed bearings and grinding spindles.

BENEFITS:

  • Improves performance.
  • Saves Energy.
  • Reduces maintenance.
  • Increases equipment life.
  • Stable at very high speeds.

PACKING: 27-litre drum and 210-litre drum

For Simplex Collars

CVC SLT OIL SPECIAL is a specially formulated synthetic oil with additives suitable for the lubrication of Simplex Collars of speed frames used in the Textile industry. It is a non-staining non-sticking, long-life lubricant, which does not allow cotton fluff, dirt and dust to the spindle, thus ensuring long term lubrication. The oil has been formulated with special additives, which form a lubricative film on the spindle over which the synthetic oil slides. For this reason, initially the dosage of oil is higher till the lubricative film is formed by additives. Subsequently the replenishment dosage of CVC SLT OIL Special reduces greatly and thereby providing economic lubrication.

DOSAGE & METHOD OF APPLICATION:

For lubricating the spindle for the first time with CVC SLT OIL Special, please clean the spindle thoroughly from the previous oil, dirt, dust and the accumulated cotton fluff. After thoroughly cleaning the spindle, apply CVC SLT OIL Special in the following manner:

Squeeze 20 drops of CVC SLT OIL Special per spindle to wet it thoroughly.
After 5-days of running, please apply 15 drops of the spindle.
After 10days again apply 15 drops and subsequently replenish with 10 drops of CVC SLT OIL Special to the spindle every 10 days.
Please ensure that during every cleaning schedule, the inner portion of the bobbins should be cleaned.

Unit Packing: 100-ml. Plastic bottle

Synthetic Ring & Traveller Oil for reducing Yarn Imperfections

CVC RINGLUBE® is a revolutionary high performance non-staining low friction antistatic synthetic oil specially developed for the lubrication of Ring and Ring Travellers in the Ring frames of Textile Mills. CVC RINGLUBE does not leave any carbonaceous deposit and therefore will increase the productivity and life of Ring Travellers considerably. It reduces yarn imperfections and increases the life of ring travellers.

It is clear transparent washable oil with low viscosity, suitable for most applications. If necessary, the viscosity of this product can be varied to take care of special conditions to suit varying duty.

APPLICATION (GUIDE LINES)
For first time lubrication

  1. During the normal maintenance period, clean the rings thoroughly with clean lint free hosiery fabric piece.
  2. Wet the hosiery fabric with CVC RINGLUBE Oil and apply on the rings.
  3. Also wet the ring travellers with CVC RINGLUBE before fixing them on the rings.

For subsequent lubrication
According to the requirement, apply CVC RINGLUBE Oil on the rings by wet/lubricated hosiery fabric.
or
with Dropper bottle
a) Use 1or 2 drops per ring once every week or ten days.
with Spray tin
b) To spray once every week or ten days in running condition.
(To avoid production loss, apply the RINGLUBE Oil, during doffing time only).

BENEFITS:

  • A non-staining oil and self-cleaning oil.
  • It reduces yarn imperfections
  • Having antistatic and antirust properties.
  • Does not leave any carbonaceous deposit.
  • Keeps Ring travellers shiny by preventing tarnishing.
  • It reduces the power consumption by reducing friction.
  • It increases life of Ring Travellers by reducing their wear.
  • It reduces operating temperature of Ring Travellers.
  • Eco friendly oil.
  • It allows increase in the Spindle speed by about 1000 RPM thus increasing Productivity by 7%.

PACKING: 100-ml.dropper bottle, 550-ml. Aerosol tin

High Speed Rotor Oil

It is a highly stable synthetic lubricant designed for operating under high dynamic loads where speeds are also very high in order of 80,000 – 1,00,000 RPM. It is normally used in place of SYNOL RG-10 (High Speed Grease) used in rotor bearings of Open-End-spinning machines operating at higher speeds where oil lubrication is preferable to grease lubrication.

It is also a high temperature long life lubricant where operating temperature go beyond 220°C.

AREAS OF APPLICATION:

It is used for the clutch of the feed speed variable gear box, reverse motion feed box bearings and gears of Open-End spinning machines.

BENEFITS:
Long life lubricant for high speed applications.
Excellent lubricity and low friction under high dynamic loads.

PACKING: 1-litre plastic bottle.

High Speed Rotor Oil

It is a highly stable synthetic lubricant designed for operating under high dynamic loads where speeds are also very high in order of 80,000 – 1,00,000 RPM. It is normally used in place of SYNOL RG-10 (High Speed Grease) used in rotor bearings of Open-End-spinning machines operating at higher speeds where oil lubrication is preferable to grease lubrication.

It is also a high temperature long life lubricant where operating temperature go beyond 220°C.

AREAS OF APPLICATION:

It is used for the clutch of the feed speed variable gear box, reverse motion feed box bearings and gears of Open-End spinning machines.

BENEFITS:
Long life lubricant for high speed applications.
Excellent lubricity and low friction under high dynamic loads.

PACKING: 1-litre plastic bottle.

Semi-Synthetic Gear Oil

This is a semi-synthetic high viscosity gear oil used especially for long term lubrication of gears and gear boxes subject to heavy loads on continuous basis. It is fortified with antioxident, corrosion inhibitor and EP additives.

AREAS OF APPLICATION:
Variable speed gear box of draw-off and other gear boxes of open end spinning machines. Enclosed Gear drives, Windmills, Transmission chaims, Heavily loaded low speed antifriction bearing, Centralised lubrication systems.

BENEFITS:

  • Extends drains intervals.
  • Reduces wear and tear.
  • Wide operating temperature range.
  • Reduces power consumption.
  • Chemically inert.

PACKING: 27-Litre drum.

Synthetic Knitting Oil

It is a fully formulated Synthetic Knitting oil, especially designed for the lubrication of needles of circular knitting machine to provide long life and extremely low friction performance. It is a non-staining synthetic oil which does not leave any carbonaceous deposit and due to its excellent lubricity, it reduces the power requirement of the drives. Its mild antistatic and antirust properties make it suitable for use in high speed knitting, texturizing and winding machinery employed in Textile and Polymer industries. It is approved by Mayer, Terrot, Fukuhara and other leading manufacturers of Knitting Machinery. It also passes the environmental requirements of European & America Oeko-Tex standards as safe, non-polluting and eco-friendly product.

BENEFITS:

  • A non-staining oil and self-cleaning oil.
  • Having antistatic and antirust properties.
  • Does not leave any carbonaceous deposit.
  • Keeps needles shiny by preventing tarnishing.
  • It reduces the power consumption by reducing friction.
  • It reduces operating temperature of knitting machines.
  • It improves productivity by allowing operation at higher speeds.

PACKING: 27-litre drum & 210-litre Drum.

Non-staining Stitching Oil

CVC STITCHLUBE is a fully formulated stitching oil, specially designed for the lubrication of modern sewing machines such as JUKI, PEGASUS, PFAFF, SUNSTAR, SIRUBA, SINGER, BROTHER, YAMOTO, REECE, RIMOLDI etc. It lasts much longer then the conventional petroleum oils. Because of its low friction, it reduces power consumption. It is a non-staining oil. It does not leave any carbonaceous deposit and reduces maintenance costs considerably. The oil is completely water washable and it does not leave any stain after the fabric is washed. It is available in different viscosity grades if required.

BENEFITS:

  • A non-staining oil and self-cleaning oil.
  • Having antistatic and antirust properties.
  • Does not leave any carbonaceous deposit.
  • Extends needle life.

Note:-
For best results, it is necessary to flush out the previously used oil and clean the machine for 30 minutes with our FLUSHKLEEN Oil before switching over to our Synthetic oil STITCHLUBE in the Sewing machines.

PACKING: 27-Litre Drum & 210-Litre Drum

High Temperature Chain Oil

CVC VISCOLUBE (HT) is a fully synthetic chain oil, specially designed for the lubrication of Stenter chains, to provide high temperature, anti-wear performance. It is a synthetic oil, which does not leave any carbonaceous deposit and due to its low friction, it reduces the energy requirement of stenter drive. It extends the maintenance shutdown period of chain cleaning in stenters.

It is used for all types of stenters including heat setting types upto 250°C and therefore more suitable for higher temperature application and longer duration applications than conventionally used chains oil. It can also be used for high temperature conveyor bearings of paint ovens and furnaces etc. It is also an eco-friendly, biodegradable chain oil.

BENEFITS:

Lowers energy consumption.
Reduces friction and wear.
Acts as clean, non-carbonizing lubricant to prevent jamming.
Operates at very high temperatures.
Reduces maintenance down time.
Eco-friendly oil.

NOTE: Other viscosity grades are available upon request.

PACKING: 27-litre drum and 210-litre drum

Washable Oil for Looms

A unique, water washable, non-staining, synthetic lubricant for centralized lubrication system (oil box) for all types of weaving looms. It has a long life because of its excellent oxidation stability. The inherent nature of synthetic oil has very low friction & wear and also because of its anticorrosive property it extends life of all moving parts lubricated by it. It sticks to the chain and other moving parts of looms tenaciously for long term lubrication.

AREA OF APPLICATION:
For centralized lubrication system of types of weaving looms, viz. Piccanol, Dornier, Sulzer, Kayang Yhe, Sara Bonas, etc. It is sprayed through oil box on the reed chain motion of Sulzer looms.

BENEFITS:

  • Prevent visible, undesirable stains.
  • It is easily washable.
  • Enhances lubrication by reducing friction.
  • Saves Energy.
  • Lasts long.

PACKING: 27-litre drum & 210-litre drum

Antistatic Agent

CVC NT STAT- 40 is a versatile antistatic agent, which can be used on all types of synthetic fibres and their blends.

It exhibits excellent lubricating characteristic both fibre-to-fibre and fibre-to-metal.

It shows low fibre metal friction, medium to low inter fibre cohesion and is, therefore, ideally suited as a balanced product for static control on fibres.

CVC NT STAT- 40 is used as an effective lubricant for blending of various fibres. It is specially suitable for wool synthetic blends since it produces good inter fibre cohesion, sufficient lubrication and minimum static which are essential for the efficient working of fibre.

It can impart slightly crisp handle on the thread fibre without being sticky. The lubricate fibres shows very uniform level of friction and have a steady even draw in sliver form resulting in easier and more regular drafting at intersectors rovers and spinning frames.

Treatment of fibres with CVC NT STAT-40 ensures better level and stronger yarns with reduced fly wasted and reduced slubes and nips, thereby improving the rate of production at combing and recombing stages. It also ensures more uniform blending of wool / synthetic fibres.

CVC NT STAT-40 should always be applied from an aqueous solution by means of an accurate metered spraying device since this equipment can consistently measure small quantities.

It can be applied to tow, converted slivers, gilled sliver or staple fibres and also as a corrective finish for synthetic fibres and their blends.

Dissolving Method: CVC NT STAT-40 can be diluted with water in any proportions.

GUIDELINES FOR APPLICATION: The quantity of CVC NT STAT – 40 to be used will depend
upon the nature of system adopted.

Guidelines for some of the applications are give herebelow:-

1. For staple fibres:

Normally 5 – 10 % solution of CVC NT STAT – 40 when sprayed on fibrous mass can achieve effective and uniform static control.

2. For Slivers:

When treating slivers at pacific converter or Turbo Stapler, 25% aqueous solution of CVC NT STAT-40 is recommended at Crimper rolls.

In case of spraying slivers on Intersector gill boxes, 25 to 40% solution of
CVC NT STAT-40 may be used.

3. For blending of wool with Synthetic fibres:

For blends of wool and staple fibres spun on the continental, or French system, very small quantities of antistats are normally used. Unless the lubricant is extremely effective, rollers and apron lapping can be a serious problem in such cases. CVC NT STAT-40 is the most effective lubricant for ensuring trouble free operations on such systems. For wool / synthetic blends, 0.75% to 0.85% of CVC NT STAT-40 is sufficient to give desired results.

4. For Dyed tows and tops:

Normally, CVC NT STAT-40 is applied on synthetic fibres, dyed tows and tops as a corrective finish. The quantities to be applied are given herebelow:-
a) As corrective finish for synthetic fibres, and dyed tows: 0.25 o.w.f.
b) As a replacement for producers, finish on dyed top:
c) For polyester staples to be processed on cotton or semi worsted system: 0.2 to 0.3 o.w.f.
d) For dyed staples on woolen systems: 0.75 to 1.0 o.w.f.

The above quantities mentioned on the weight of fibre are given as a general guideline and the exact quantities monitored should be decided looking into type of fibres. Natures of producer’s finish and type of fibres. Natures of producer’s finish and type of operations so that effective static control without the problems of card loading is achieved.

Storage Stability: About 12 months at normal conditions of storage.

Product may congeal at low temperatures and may be used after thawing and stirring.

Packing: 27-Litre & 210-Litre drums

Antistatic Coning Oil for Synthetic Fibres

NT-STAT-52 is a thermally stable compound, which has been developed as a lubricant for texturising of nylon and polyester yarns. It is substantive to nylon and polyester and forms a strongly adherent film with the highest intermolecular cohesion, imparting low and uniform frictional properties to these fibres.

With regards to friction and lubrication of synthetic fibres, the behaviour of synthetic fibres can be divided into 3 categories, namely, the boundary, semi-boundary and hydrodynamic. The hydrodynamic friction is ascribed in the speed range above 5.5 meters per minute. It follows that intermittant contacts between fibres and substrate exist in the boundary region, whereas a continuous fluid film separates fibre from substrate in the hydrodynamic region.

NT-STAT- 52 has high wetting property for nylon and polyester. This is clear from the surface tension data as under: –

Nylon : 46 dynes / cm.
Polyester : 43 dynes / cm.
NT-STAT- 52 : 30 dynes / cm.

This clearly indicates perfect wetting of NT-STAT- 52 for those above two fibres.

Another important parameter in the fibre lubrication is lubricant viscosity. The viscosity of NT-STAT 52 is adjusted to reduce the sheer stress in the hydrodynamic region thereby decreasing the friction, in the boundary region, of course, the friction is independent of lubricant viscosity. It is worthwhile to mention that there is no significant difference between frictional behaviour at the fibre to metal and fibre to fibre interfaces.

Other Textile finishing oils and spin finishes are also available.

Packing: 27-Litre & 210-Litre drums

Greases

Off-white High Temp. Grease for Draw Frames

It is a specially blended formulation if complex soap off-white grease fortified with special additives to meet critical industrial applications in the textile and engineering industries. It is especially suited for the lubrication of high speed, high temperature, ball and roller bearings, needle bearings and plain bearings under heavy loads.

It is a highly adhesive, friction reducing, withstanding extreme temperature/load, water repellent grease suitable for a wide variety of industrial applications.

APPLICATION:
For the lubrication of top roller and bushes of DO / 2S and DO / 6 and RSB draw frames manufactured by LMW. Similar application where needle are used under heavy loads.

BENEFITS:

  • Withstands high Temperature & heavy loads, typical in Textile Mill application.
  • Off – White grease, which can substitute black moly grease.

PACKING: 1-kg.jar & 10-kg.bucket

 

Non-melt/ Non Drip, Moly Grease

It is a specially blended grease with a Synthetic thickener and fortified with Molybdenum disulphide and other special additives to meet heavy duty, critical industrial applications in the textile and engineering industries. It is especially suited for the lubrication of high speed, high temperature, ball and roller bearings, needle bearings and plain bearings under heavy loads.

It is a non-melt / non drip, highly adhesive, friction reducing extreme temperature / load, water repellent multipurpose grease suitable for a wide variety of industrial applications.

APPLICATIONS :
For Conveyor bearings, Oven chains, induced draft fan bearings, Heavy duty Earth moving equipments, Drives, Furnace door & Hinges, Agitator, Mixers, etc.

BENEFITS :

  • Non-melt / Non-drip grease to reduce contamination.
  • Withstands heavy loads/ High temperature.
  • Reduces maintenance downtime.
  • Highly adhesive to metals.
  • Long life lubricant.

PACKING: 1-kg.jar, 10-kg.bucket & 180-kg.drum

Heavy duty / High Temperature Moly Grease

It is a specially blended formulation of complex soap based grease fortified with Molybdenum disulphide and other special additives to meet critical conditions for automotive and industrial applications. It is specially suited for the lubrication of high speed, high temperature, ball and roller bearings, needle bearings, plain bearing, king pins, ball joints, linkages etc. under operating temperature and environmental adverse conditions such as heavy loads, corrosion and dusty atmosphere.

It is a highly adhesive, friction reducing extreme temperature/ load, water repellent multipurpose grease suitable for a wide variety of industrial applications.

Temperature Range: -40°C to 250°C

APPLICATIONS :
For Ball and Roller bearings operating under high speed and high temperature, King pins, Ball joints, Gears, Linkages, Speed reducers, Splines, Stenter fan bearings etc.

BENEFITS :

  • Heavy duty / High temperature grease.
  • Highly adhesive.
  • Reduces maintenance downtime.
  • Operates effectively under adverse conditions.

PACKING: 1-kg.jar and 5-kg. bucket

High Temperature Grease for Draw Frames

It is a specially blended formulation of synthetic complex soap grease fortified with special additives to meet critical industrial applications in the Textile industries. It is especially suited for the lubrication of high speed, high temperature, ball and roller bearings, needle bearings and plain bearings under heavy loads.

It is a highly adhesive, friction reducing, withstanding extreme temperature /load, water repellent grease suitable for a wide variety of industrial applications.

APPLICATIONS :
Specially for the lubrication of top roller and bushes of RSB draw frames manufactured by LMW and DO / 2S and DO /6. Similar application where needle bearings are used under heavy loads.

BENEFITS :

  • Withstands high Temperature & heavy loads, typical in Textile Mill application.
  • Non-staining, Off-white grease which can substitute black moly grease.

PACKING: 1-kg.jar & 27-kg.drum

High Speed Rotor Grease

It is a synthetic fluid grease specially formulated with highly stable chemical additives for high speed operations. These special chemical additives reduce the fatigue and abrasive wear considerably under extreme dynamic load conditions where operating speeds and temperature are too high. It is also suitable for centralized lubrication system where fluid greases are required to reduce their internal friction and pumping losses.

AREA OF APPLICATION:

High Speed Bearings, FHP motors, Instrument bearings, Gear couplings, High Speed Centrifuges, Internal grinders, Manhot spindle etc. of CNC machines.

BENEFITS:

  • DN Factor: 1,000,000.
  • Operates under very high speed / temperature.
  • Energy saving.
  • Reduces wear and tear at high speed.
  • Reduces down time.

PACKING: 1-Kg. Jar and 15-Kg. Bucket

Non-Staining Grease

It is a white grease, especially developed where staining from lubricants is not desirable such as in Textile Spinning, Knitting, Weaving & Processing units. It can also be useful in Printing presses and white goods manufacturing units. SYNOL NSG-100 has been formulated to give better performance at high speeds with good tolerance to humidity. It is specially recommended for Ring frame Top & Bottom roller bearings, Textile looms and process machinery bearings and other similar applications.

AREA OF APPLICATION:
All types of anti-friction bearings, open gears, Chains and sliding surface where staining of lubricant is not tolerable, suitable for centralized lubrication system.

BENEFITS:

  • Non-staining.
  • Reduces friction and wear.
  • Shortens maintenance downtime cost.
  • Chemically inert and water repellant.

PACKING : 1-Kg.Jar & 15-kg.bucket

Anti-Seize Compound

SYNOL MOLYPASTE N-3 is a highly concentrated micro size Molybdenum disulphide based multipurpose assembly/lubricating paste fortified with special additives to withstand very high temperature and extreme loads. It is most ideally suitable as an assembly paste for grease lubricating system to ensure freedom from scuffing and scoring. MOLYPASTN-3 eliminates metal to metal contact between nuts and bolts preventing them from seizing leading to breakage under extremely heavy load.

AREA OF APPLICATIONS :

  • To prevent seizure in the cases of nuts, bolts, studs, screws, locknut, pipes and coupling, unions, U-bolt, flanges exhaust manifolds, Chuck lubrication, live centre, press fits and assembly etc.
  • It is used as an assembly paste for grease lubricated systems such has bearings, gears, piston rings, valve systems and for parts impossible to be lubricated in service to ensure freedom from scuffing or scoring during the initial operation period.
  • For all overloaded and overheated bearings to prevent seizure and as a coolant.
  • To eliminate scoring during press fitting.
  • During shock loading of the bearings either of the radial or of the axial type this lubricant prevents metal to metal contact between the ball and the race and thereby prevents seizure and galling.
  • To prevent wear, sticking and corrosion for valves cocks etc.
  • To prevent thereby increasing the useful life of bearing and lubrication period i.e. time between two successive grease application.
  • For all slides, ways, guides subjected to heavy intermittent loads.
  • 5th wheel assemblies, king pins, splines sleeves etc.
  • Chains, cables, linkages, speed reducers, rim locking rings.
  • To protest metal parts from Rust and Corrosion when subjected to humidity and corrosive atmosphere.
  • It is also used as a heavy thread lubricant and for Chuck lubrication.

BENEFITS:

  • Prevents seizure under heavy loads, for all threaded connections
  • Easy and quick dismantling of mechanical parts
  • Heavy duty thread lubricant which protect threads from rust & corrosion
  • An effective press fitting and assembly aid.

PACKING : 100-gm. jar, 1-kg. jar and 5-kg. jar

Coatings

Dry Film Moly Spray

Similar to CVC Molytex but it is a Dry Film lubricant for cams where lubrication is not desirable

Antiseize Compound

It is a highly concentrated micro size molybdenum disulphide based multipurpose lubricating paste.

It is used as an assembly paste for grease lubricated systems such as bearings, gears, piston rings, valve systems and for parts impossible to be lubricated or inaccessible in service to ensure freedom from scuffing or scoring during the initial operation.

It is an excellent heavy duty thread lubricant operating from -40º C to 1100º C to prevent seizure in the cases of nuts, bolts, studs, screws, locknuts, pipes and couplings, unions, U-bolts, flanges, exhaust manifolds etc.

Unit Packing: 1-kg. Jar

It is highly stable synthetic lubricant designed for operating under high dynamic loads where speeds are also very high in order of 80,000 – 100,000 RPM.

It is normally used in place of SYNOL RG -10 grease such as in rotor bearings of Open-End spinning machines operating at higher speeds where oil lubrication is preferable to grease lubrication. It is also a high temperature long life lubricant where operating temperatures go beyond 220º C.

Unit Packing: 1-litre plastic bottle and 5-litre Carboy.

Synthetic Oil for Textile Stenter

This a fully synthetic chain oil, specially designed for lubrication of stenter chains, to provide high tempreture, anti-wear performance. It is a synthetic oil which does not leave any carbonaceous deposit and due to very low friction, it reduces the current requirement of stenter drive. It is used for all types of stenter including heat setting types upto 240º C and therefore more suitable for higher temperature application and longer duration applications than conventionally used chains oil. It is also used for synthetic leather cloth stenter applications and circular looms. Other uses that it can be used for high temperature conveyor bearings of paint ovens and furnaces etc.

Benefits :
 Lowers energy Consumption
Reduces friction and wear.
Acts as clean non-carbonizing Lubricant to prevent jamming.
Operates at very high temperatures.
Reduces maintenance down time.

Packing: 5-litre Carboy, 25-litre Drum and 200-litre Drum.

Lubricants

Anti-Static Reed Wire Cleaner

An excellent Anti-Static agent with Synthetic lubricants specially developed for cleaning the yarn deposits, fluff, dust & other contaminants on the reed wires of high speed looms. The non-staining Synthetic lubricant ensures lubrication of the reed wires preventing further fluff deposits without affecting or harming the reed or the fibre.

APPLICATIONS :
For cleaning yarn deposits on the reed wires of high speed weaving looms. It may also be used for removing fluff and other contaminants on other Textile Machines and protect them from rust.

BENEFITS :

  • An excellent cleaner for filament and yarn deposits on the reeds.
  • Protects from Rust & corrosion.
  • Lubricates Reed wires & Increases life.
  • Does not attract fluff, dust etc. being Anti-static in nature.

PACKING: 550-ml. Aerosol Tin.

Knotter / Splicer Cleaner

TEXLUBE is a non-staining cleaner-cum-lubricant for modern textile machinery used for various operations such as Spinning, Winding and Weaving, Knitting etc. Based on a specialty cleaner, synthetic lubricant and other chemical additives, it immediately penetrates and cleans fluff, dust and other deposits accumulated on surfaces. Further it leaves a thin, non-staining and non-sticky film of lubricant, which protects the exposed surface form rust & corrosion and reduces the wear & tear of moving parts. It is specially formulated for knotter/splicers of Schlafhorst, Murata Savio & Padmatex autowinders.

BENEFITS:

  • Cleans Carbon & Fluff deposits.
  • Lubricates the delicate Machinery.
  • Protects from rust and corrosion.

AREA OF APPLICATION: Knotter of autoconers and winders, spinning and weaving machinery, knitting and sewing machines, delicate mechanisms and other high speed equipments.

UNIT PACKING: Available 550-ml.Aerosol Tins with extension lube for pinpoint application.

Rust Preventives

(Rust Remover Fluid)

CVC SUPERSTRIP-200 is the latest formula 3-in-1 rust removing solution for fast and economic removal of rust and scale from iron & steel surfaces. Moreover, SUPERSTRIP-200 is safer to handle than similar conventional acidic products and it leaves a phosphate coating which protects from immediate rusting.
It is based on light acids, accelerators, solvents, surface active agents and inhibitors for quick degreasing, rust removing and phosphating action. It is used in concentration of 10 to 50% with water at temperatures ranging from room temperature to 80°C. The higher the temperature and concentration, the faster the results. Normally 10-20 minutes are allowed after application for the SUPERSTRIP-200 to act before scrubbing with wire brush for removing rust and final rinsing with water.

AREA OF APPLICATION :
Although SUPERSTRIP-200 is non-flammable and non-toxic, contact with hands   and eyes should be avoided by wearing rubber or plastic gloves and goggles.  Any splash on skin should be removed by copious quantities of water.

BENEFITS :

  • Specially designed to clean the surface, remove the rust quickly and phosphate it in one single operation.
  • A powerful metal preparation solution for superior painting and coating.
  • It assures proper adhesion of all types of coating by it excellent surface preparation.
  • Economically, eliminates costly and time consuming 5-stage.
  • Easy to use, simple one step mixing formula, simplifies inventory controls and saves money!

PACKING : 5-litre Tin, 27-litre & 210-litre drum

(Rust Convertor)

CVC RUSTKOTE-300 is a new generation protective coating, which converts existing rust on metallic surfaces into a chemically inert coating, which prevents further rust and provides a suitable base for painting immediately. RUSTKOTE-300 is a neutral solution of active chemical ingredients incorporating mineral acids, solvents, stabilizers and additives. It saves expensive and time consuming scrapping of tenacious rust by sand blasting etc.
RUSTKOTE-300 can be used on rusted as well as clean metal surfaces. Due to the formation of inert coating, further rusting is totally stopped. It reacts with the loose and adherent rust on the metal surface and converts the rust into a very inert and adherent organo-metallic coating.

AREA OF APPLICATION :
It can be used on fabricated steel component bridges, girdles, chimneys, heavy machinery, structures, trusses underground and open pipe lines, electric poles petrochemical and power plants, irrigation and dam structures.

BENEFITS :

  • Excellent corrosion prevention.
  • Resistant to mild Acids & Alkalis.
  • Pre-cleaning cost is reduced.
  • Easy to handle.
  • Withstands temperatures upto 400°C.
  • Very economical solution.
  • Non-toxic , Non-hazardous.

PACKING : 5-litre Tin, 27-litre & 210-litre drum

(Dry Film Rust Preventive)

CVC NT-RUST (DF) is a light-bodied pale coloured consisting of high molecular weight resin with Rust Inhibiting additives in a solvent base.  The solvent will evaporate from the coated parts leaving a thin transparent film, which is shiny in appearance and non-brittle.  This is a flexible film and is suitable for protection of metal parts exposed to the atmospheric rust at moderate temperatures under mild acidic and alkaline conditions.

AREA OF APPLICATION :
All Metal parts such as nuts & bolts, components, sheet metal plates, bearings, chains, hardware items  for indoor/outdoor protection and for exports.

BENEFITS :

  • Dry film rust preventive.
  • Easily removable when required.
  • Economic Protection.

PACKING : 550-ml.Aerosol Tin, 5-litre Tin, 27-litre & 210-litre drum

(Strippable Rust Preventive Coating)

CVC STRIPKOTE is based on a polymeric substance dispersed in wetting agents, organic solvents, film leveling agents, dryers and plasticizers for attaining mechanical strength to the film.  It  leaves a very thin rust protective coating dried film on the surface which will be non permeable to water, acids, alkalies and to any atmospheric attack.  The film will offer excellent protection against atmospheric corrosion for a period of 12 months indoors & for a period of 6 months outdoors, while the components are stored in a covered shed.   This rust preventive coating can be easily removed by peeling it off like a banana skin when not required.   It can be used as supplied without any dilution for brushing application.

AREA OF APPLICATION :
Automobile pressed components of CRCA, fabricated MS sheet metal doors & window sections, Machinery parts, Machined components, Anodized aluminium metal labels, Doors & windows sections, Appliances etc.

BENEFITS :

  • Protects from rust & corrosion without affecting the surface.
  • Easily peelable protective film.
  • Easily removable whenever required.

PACKING : 5-litre Tin, 27-litre & 210-litre drum

(Non-drying oily Rust Preventive)

CVC NT-RUST (LQ)  is a petroleum based rust preventive which forms a soft oily film over the metal surface. It is used for protection of exposed gear boxes, internal gear boxes, steel sheets during transportation, hydraulic systems I.C. engines etc. The oil film can be removed easily by wiping or with the help of solvents.

AREA OF APPLICATION :
Gear boxes, internal gear boxes, steel sheets during transportation, hydraulic systems I.C. engines etc.  It can be applied by dipping or spraying.

BENEFITS :

  • Excellent Rust Preventive.
  • Economic Protection.

PACKING : 5-litre Tin, 27-litre & 210-litre drum

(Waxy Rust Preventive)

CVC NT-RUST (WX) is a petroleum based rust preventive which forms a soft waxy film over the metal surface. It is used for protection of exposed gear boxes, internal gear boxes, steel sheets during transportation, structurals, hydraulic systems, I.C.engines and moulds of plastic components etc. The waxy film can be removed easily by wiping or with the help of solvents. This product is available in any other colours such as Blue, Green, Red etc. for bulk requirement.

AREA OF APPLICATION :
Gear boxes, internal gear boxes, steel sheets during transportation, hydraulic systems, I.C. engines etc.  It can be applied by dipping or spraying, the  Moulds of plastic components and Structures exposed to salty weather.

BENEFITS :

  • Excellent Rust Preventive.
  • Long lasting & Non-staining.

PACKING : 550-ml.Aerosol Tin, 10-kg. bucket & 180-kg. drum

(Volatile Corrosion Inhibitor Spray)

CVC NT-RUST (VCI) is a Volatile Corrosion Inhibitor rust preventive which is available in Spray form. It is used for the protection of enclosed electronic circuits, control panels, etc. It is also used for the small tools & parts in storeroom against rust & corrosion. Once sprayed it quickly spreads in vapour form to envelope the entire enclosed area for rust & corrosion protection in the storeroom.

BENEFITS:

  • Excellent Rust Preventive.
  • Long lasting & Non-staining.
  • Easy to spray in large enclosed storage spaces.

PACKING : 550-ml.Aerosol Tin

Spinnerette Spray

Spinnerette Spray for Nylon & Polyesters

A high grade custom formulated Silicone based heavy duty release agent for synthetic fibres such as Nylon, Polyesters, Acrylics, etc. It is formulated with thermally stable Silicones, which resist high temperature with low volatility. It is regularly sprayed on spinnerets through which synthetic filament yarn is drawn, so that sticking of filaments with one another or with spinneret is avoided. It also makes higher temperature extrusion possible to increase production of synthetic filaments.

The product can also be formulated in line with the quality of silicone (for long life, high temperature) & its content and type of propellant (flammable / non-flammable) to meet the customers requirements.

AREA OF APPLICATION :
On the spinnerets of spinning melt systems for Synthetic fibres. As a high temperature lubricant for Bearings, Chains, Gears, Guides etc.

BENEFITS :

  • Non-sticking Release Spray.
  • Less volatility at high temperature.
  • Extended Cleaning intervals.
  • Non-Toxic & Non-Flammable.

PACKING : 550-ml. Aerosol Tin